To obtain your inv. code (registration code) kindly contact [email protected] Please note that, guests have limited sections to view
If you are a registered member in MHH and not able to login or recover your account, Kindly contact [email protected]

Thread Rating:
  • 46 Vote(s) - 2.91 Average
  • 1
  • 2
  • 3
  • 4
  • 5
All About Carprog Clone
#46
(04-18-2018, 01:32 PM)danngrigore Wrote: Hi guys
I wish somebody could give me a hint about my issue with my Carprog. Recently I had to replace the AT91 processor because of a failure. I have fitted brand new one, wrote the firmware as per instructions, done all the modifications, all went good. Now when I start Carprog software no matter what version, with or without correct lib file, the software shows on the bottom left “Device sn:” but after this is blank. No serial number at all. And because of this (or some other reason?) the software does not let me do anything. Please help me find out what I am missing.
Thanks
You must repeat the procedure. Something went wrong during programming.
Reply
Thanks given by:
#47
(07-04-2018, 02:21 AM)darkmal Wrote:
(04-18-2018, 01:32 PM)danngrigore Wrote: Hi guys
I wish somebody could give me a hint about my issue with my Carprog. Recently I had to replace the AT91 processor because of a failure. I have fitted brand new one, wrote the firmware as per instructions, done all the modifications, all went good. Now when I start Carprog software no matter what version, with or without correct lib file, the software shows on the bottom left “Device sn:” but after this is blank. No serial number at all. And because of this (or some other reason?) the software does not let me do anything. Please help me find out what I am missing.
Thanks
You must repeat the procedure. Something went wrong during programming.

Wrong chip fitted. Only revision a and b work. I have some for sale if interested.
Reply
Thanks given by:
#48
ı updated carprog v8.21 but conncect to pc and unknown devices. what is problem. can you help me pls...
Reply
Thanks given by:
#49
(07-04-2018, 07:30 PM)multialper Wrote: ı updated carprog v8.21 but conncect to pc and unknown devices. what is problem. can you help me pls...
Make the procedure from the beginning as described below.

1. Take out the soic AT88sc from the board, lift pin 55 of processor and solder a wire to pin 55.
2. Connect carprog main unit to the computer, after 20 seconds disconnect it.
3. Connect carprog main unit to the computer, place the wire(pin 55) on VDD for about 20 seconds, now place the wire on ERASE for about 20 seconds after that disconnect carprog from the computer.
4. Now you can connect carprog main unit to the computer, you will notice that this time windows is going to recognize it. Just start the programming procedure.


Attached Files
Carprog VDD and ERASE.png
File Type: .png
Downloaded: 52 times
Size: 985.82 KB

Reply
Thanks given by:
#50
(07-04-2018, 07:53 PM)darkmal Wrote:
(07-04-2018, 07:30 PM)multialper Wrote: ı updated carprog v8.21 but conncect to pc and unknown devices. what is problem. can you help me pls...
Make the procedure from the beginning as described below.

1. Take out the soic AT88sc from the board, lift pin 55 of processor and solder a wire to pin 55.
2. Connect carprog main unit to the computer, after 20 seconds disconnect it.
3. Connect carprog main unit to the computer, place the wire(pin 55) on VDD for about 20 seconds, now place the wire on ERASE for about 20 seconds after that disconnect carprog from the computer.
4. Now you can connect carprog main unit to the computer, you will notice that this time windows is going to recognize it. Just start the programming procedure.

Don't follow this procedure. Reset is not where its shown in the picture. Its exact opposite where VDD is shown.
Reply
Thanks given by:
#51
Hi , Bought a China Carprog as wanted to test the land rover terrain Module Millage correction but it says that its not activated on that page . ( i think i have a v4.01 unit ) .

I have had a little read and i assume i need the v8.21 Firmware for the online version and need to flash this.

Cant find definitive information on what is required to flash this , do i need to modify the hardware and flash with a usb programmer module ? if so does any one have a guide on what i need to do ?

Also am i right in assuming that a lot of the OBD functions of carprog are locked because of the older offline firmware ?

Thanks
2097
Reply
Thanks given by:
#52
Does anything from list work with Carprog clone? I mean online functions, like VAG 2009-.

[Image: attachment.php?aid=274191]
Reply
Thanks given by:


Possibly Related Threads...
Thread Author Replies Views Last Post
Renult Software Renault Clip Tool ALL IN ONE Free fo all samatii 6 1,108 10-07-2018, 02:56 AM
Last Post: Tomaszsz
  carprog activation online bzykupiotrek 288 18,437 08-25-2018, 02:20 AM
Last Post: Balyanchic
  Carprog activation sholarx 10 795 07-24-2018, 10:22 AM
Last Post: manusu
  wanted carprog with opel opec28 red patrol 1 137 07-19-2018, 01:47 PM
Last Post: oli1
  CARPROG v8.21 Keygen free for ALL MHH members Lauris1988 2 696 06-25-2018, 01:06 AM
Last Post: Lauris1988



Users browsing this thread: 1 Guest(s)


This forum is for experimental & educational purposes only. As such, it is not acceptable whatsoever to post any software that requires a license on this forum. If any member does this, she/he will be revoked her/his membership forthwith. The forum greatly appreciates the cooperation of its members on this critical issue.
Best Viewed with Chrome.