Hi all members 
One my friend brought me a multiplexer (its not classic C3 MUX, its analog without any markings), so I figured out why he is cann't connected to the car.
He also brought a laptop with installed DAS 01/2008
.
![[Image: Файл_002(1).jpg]](https://s19.postimg.org/wfrwej6gf/Файл_002(1).jpg)
First of all I made Caesar selftest ->
![[Image: Файл_003(1).jpg]](https://s19.postimg.org/6zjfocqjz/Файл_003(1).jpg)
I was immediately alarmed by the error 1802. I re-solder all pins of microcontroller SAF-C167 and SecureFlash x76F041A.
Ineffectually
Considering PCB further I found two bloated capacitors 12V circuit. I replace them. (Then I looked at the 1st results of the test, with bloated capacitors, power supply voltage is 16-17V
)
![[Image: Файл_000(1).jpg]](https://s19.postimg.org/i2ygg7mgf/Файл_000(1).jpg)
When you try to connect to the car through the DAS see error ->
![[Image: Файл_004(1).jpg]](https://s19.postimg.org/iefwsz2wf/Файл_004(1).jpg)
In 12/2014 DAS same error code, but without CAL 503 ->
![[Image: Файл_005.jpg]](https://s19.postimg.org/aodq1kpyn/Файл_005.jpg)
But most of all I was confused by the fact that I have successfully connected to the car through HHTWIN ->
![[Image: Файл_004.jpg]](https://s19.postimg.org/9827jfn1r/Файл_004.jpg)
What is it? HW problem (burned track, no power supply to EEPROM, dead SAF-C167 or x76F041A), blocked MUX for serial number or SW problem?
I need your help! I would appreciate any advice and tips. Thx
Mammoth

One my friend brought me a multiplexer (its not classic C3 MUX, its analog without any markings), so I figured out why he is cann't connected to the car.
He also brought a laptop with installed DAS 01/2008
.
![[Image: Файл_002(1).jpg]](https://s19.postimg.org/wfrwej6gf/Файл_002(1).jpg)
First of all I made Caesar selftest ->
![[Image: Файл_003(1).jpg]](https://s19.postimg.org/6zjfocqjz/Файл_003(1).jpg)
I was immediately alarmed by the error 1802. I re-solder all pins of microcontroller SAF-C167 and SecureFlash x76F041A.
Ineffectually

Considering PCB further I found two bloated capacitors 12V circuit. I replace them. (Then I looked at the 1st results of the test, with bloated capacitors, power supply voltage is 16-17V
)![[Image: Файл_000(1).jpg]](https://s19.postimg.org/i2ygg7mgf/Файл_000(1).jpg)
When you try to connect to the car through the DAS see error ->
![[Image: Файл_004(1).jpg]](https://s19.postimg.org/iefwsz2wf/Файл_004(1).jpg)
In 12/2014 DAS same error code, but without CAL 503 ->
![[Image: Файл_005.jpg]](https://s19.postimg.org/aodq1kpyn/Файл_005.jpg)
But most of all I was confused by the fact that I have successfully connected to the car through HHTWIN ->
![[Image: Файл_004.jpg]](https://s19.postimg.org/9827jfn1r/Файл_004.jpg)
What is it? HW problem (burned track, no power supply to EEPROM, dead SAF-C167 or x76F041A), blocked MUX for serial number or SW problem?

I need your help! I would appreciate any advice and tips. Thx

Mammoth
