To obtain your registration code, please send an email to [email protected]
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

smartlink c2 atsame70q20 pcb reset

1
Hello,

I need to flash smartlink c2 but programmer refuse to connect so I need to perform processor hard reset .
Does anyone know how to do it , I need information which pins have to short to reset the smartlink atsame70q20 processor ?

thanks in advance

www.pitstopobd.com  diagnostic tools and software, free EU shipping , best prices , best service
If you have any questions please contact me
Thanks given by:
2
(07-22-2026, 02:03 AM)mistery Wrote: Hello,

I need to flash smartlink c2 but programmer refuse to connect so I need to perform processor hard reset .
Does anyone know how to do it , I need information which pins have to short to reset the smartlink atsame70q20 processor ?

thanks in advance

Hi did you ever figure this out?
I am stuck on the same thing, ive got it wired up but i cant seem to connect to it with an ST-link perhaps it needs the jlink
Thanks given by:
3
Actually I got this working, I managed to dump the flash and reprogram it using openOCD and a we-act mini debugger (st-link stm32)

I could not connect to the chip with the programmers power supply and was only able to negotiate with the chip while i had external 12v on the barrel connector.

To Dump
Code:
openocd -f interface/stlink.cfg -f target/atsamv.cfg -c "adapter speed 4000" -c "reset_config srst_only srst_nogate connect_assert_srst" -c "init" -c "halt" -c "flash probe 0" -c "flash read_bank 0 firmware_backup.bin" -c "shutdown"

To write the flash 
Code:
openocd -f interface/stlink.cfg -f target/atsamv.cfg -c "adapter speed 100" -c "reset_config srst_only srst_nogate connect_assert_srst" -c "init" -c "halt" -c "adapter speed 4000" -c "program YOUR_IMAGE.bin verify reset 0x00400000" -c "shutdown"

Attached Files Thumbnail(s)
   
Thanks given by: maxxx333
4
(07-22-2026, 08:33 AM)Chilltrout Wrote: Actually I got this working, I managed to dump the flash and reprogram it using openOCD and a we-act mini debugger (st-link stm32)

I could not connect to the chip with the programmers power supply and was only able to negotiate with the chip while i had external 12v on the barrel connector.

To Dump
Code:
openocd -f interface/stlink.cfg -f target/atsamv.cfg -c "adapter speed 4000" -c "reset_config srst_only srst_nogate connect_assert_srst" -c "init" -c "halt" -c "flash probe 0" -c "flash read_bank 0 firmware_backup.bin" -c "shutdown"

To write the flash 
Code:
openocd -f interface/stlink.cfg -f target/atsamv.cfg -c "adapter speed 100" -c "reset_config srst_only srst_nogate connect_assert_srst" -c "init" -c "halt" -c "adapter speed 4000" -c "program YOUR_IMAGE.bin verify reset 0x00400000" -c "shutdown"

hmm thank you however this is not what I need . It is weird that stm32 can flash atsame . I have it but for device I use Jlink . The same problem I have with td2 but on td2 I know how to reset , so now need same information for sartlink if somebody know

www.pitstopobd.com  diagnostic tools and software, free EU shipping , best prices , best service
If you have any questions please contact me
Thanks given by:
Users browsing this thread: cipon