To obtain your registration code, please send an email to [email protected]
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

2002 Mercedes Sprinter crank but no start.

1
Hello all. 

Got a 2002 Mercedes Sprinter with the om611.987. It originally came in due to no start that was caused by glow plug relay. Noticed it was running a little unhappily so we decided to remove injectors do be sent out. Upon removal of the injectors noticed coolant coming from one of the injectors bolt holes. Cylinder head was cracked.

Removed cylinder head and replaced with refurbished head. Now the car refuses to start. When it does start with a little help from brake cleaner it’ll run a little rough at idle but when accelerated it spit out greyish smoke and knock like crazy. Clearly signs of injector. 

Injectors were swapped with known good ones. Compression was tested. Common rail and sensors swapped. Cam and crank sensors changed. Timing confirmed. High pressure pump was changed again and confirmed that it’s generating enough pressure. No codes are stored. Injector was tested outside of to check spray pattern and it’s perfect. Everything was changed including fuel line and filters. 

At a complete loss of what it could be. Any help would be appreciated.
Thanks given by:
2
In situations where it is reported—or I personally find—that there are no DTC error codes, I always perform a test and attempt to trigger errors myself; for instance, by briefly disconnecting injectors, solenoids, or various sensors. On older vehicles, where emissions-related systems (such as the EGR, swirl flaps, etc.) have frequently been removed, there is a high probability that the DTC error mask within the ECU has been deleted or heavily modified during the remapping process.
Thanks given by:
3
Is rail presuure rising enough when cranking? OM611 fuel system is infamous of drawing air at low pressure side, due to hardened o-rings or brittle hoses.
Thanks given by:
4
Ya the rail pressure reaches 450 bar during cranking. Only thing I haven't swapped is wiring harness and ecm. I did do something similar as amber has mentioned above and even confirmed that the fly wheel sensor teeth are in good shape. I have heard of the fuel system sucking air on the low side but I swapped all those tubing aside from the one that comes from the tank. I can get it running but is difficult but when it is running it'll run some what ok at idle but when you rev the engine it shows typical signs of a bad injector. Ive swapped the injectors 3 times and noticed that one set I could not get the engine to run whats so ever but part numbers for the injectors were the same.
Thanks given by:
5
Check the engine wiring harness for rubbing through on the engine mounting / bracket area where it is meant to be cable tied

I always open the loom to inspect
Thanks given by:
6
I went and double checked the wiring harness and confirmed its all good. I removed the protective sheath and inspected everything. I didnt do an ohm reading on each wire as that should throw out a etc on the ecm. I did unplug each injector while running and each one stalled the engine.
Thanks given by:
7
(11-07-2026, 12:53 PM)mtd328 Wrote: I went and double checked the wiring harness and confirmed its all good. I removed the protective sheath and inspected everything. I didnt do an ohm reading on each wire as that should throw out a etc on the ecm. I did unplug each injector while running and each one stalled the engine.

That's all a good start

So back to fuel pressures

I like to do a leak off test on the injectors, this shows if anything is major with one injector

I read that at cranking, you have 450 bar, does this rise quickly or very slowly

Normally when I have watched a vehicle running correctly, the pressure rises very quickly too 180-200 bar then the engine fires and starts, this is when you will see 300 bar (all figures are rough but for ease)

Is it not starting as there is too much pressure? is there a blockage on the return / rail pressure relief valve

Lastly, is the rail pressure value correct? so is it 0 with ignition on?
Thanks given by:
8
(11-07-2026, 01:28 PM)justin Wrote:
(11-07-2026, 12:53 PM)mtd328 Wrote: I went and double checked the wiring harness and confirmed its all good. I removed the protective sheath and inspected everything. I didnt do an ohm reading on each wire as that should throw out a etc on the ecm. I did unplug each injector while running and each one stalled the engine.

That's all a good start

So back to fuel pressures

I like to do a leak off test on the injectors, this shows if anything is major with one injector

I read that at cranking, you have 450 bar, does this rise quickly or very slowly

Normally when I have watched a vehicle running correctly, the pressure rises very quickly too 180-200 bar then the engine fires and starts, this is when you will see 300 bar (all figures are rough but for ease)

Is it not starting as there is too much pressure? is there a blockage on the return / rail pressure relief valve

Lastly, is the rail pressure value correct? so is it 0 with ignition on?
Injectors are rebuilt and confirmed good. The rail pressure will build to 250-280 bar during crank and occasionally a cylinder will fire off and the pressure will build to 400bar. pressure will normally hold at 15bar until I crack open and line in which case it'll drop to 0.
Thanks given by:
9
To add. The only thing I haven’t tried yet is program injectors into the ecm. I do not have a capable scanner as I am using autocom as it gives an error when I attempt to program.
Thanks given by:
Users browsing this thread: 2 Guest(s)