To obtain your registration code, please send an email to [email protected]
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Mercedes X290 – Snap-on “Disable ECO” – which ECU/coding does it actually change?

1
Hello everyone,
I am investigating an issue with the ECO Start/Stop retrofit function on a Mercedes-AMG GT43 4MATIC+ X290 (290.659, MY2022).
The diagnostic tool used is the Japanese Snap-on MTG-DUAL-TAB2-PRO, which uses the Autoland iSCAN / iSCAN VCI platform for European vehicles.
The menu path was:
ES (EZS213)
→ Retrofit
→ ECO
→ Disable ECO (Start-Stop System)
There is also an “Enable ECO” option in the same menu.
After running “Disable ECO”, the Start/Stop function was effectively disabled. The driver could switch ECO ON temporarily, but it would return to OFF again.
However, after this retrofit, the vehicle developed additional faults.
Main fault:
U0420EA
Invalid data received from the power steering control unit
The vehicle also showed a parking assist / PARKTRONIC warning.
During diagnosis, PTCU temporarily stored:
P164400
Incorrect variant coding / configuration detected
I restored ECO using the “Enable ECO” function in the Autoland iSCAN-based diagnostic menu.
After restoring it:
  • Start/Stop worked normally again
  • U0420EA disappeared
  • Steering warning disappeared
  • PARKTRONIC / parking assist warning disappeared
So there seems to be a strong relationship between the Autoland iSCAN “Disable ECO” retrofit and the configuration fault.
I compared several ECUs with DTS Monaco before and after the modification.
CPC_NG:
Variant: CPC_NG_R19A1
In Domain [001] I have:
  • Kopplung 3S an Fahrprogramme = 3S gekoppelt an Fahrprogramme
  • 3S LastMode = Kein LastMode 3S
  • intelligente Motorabschaltung iECO = iECO aktiv
The coding in this domain appeared unchanged before/after the retrofit.
EZS213:
Variant: EZS213_MOPF_Rel_10
No obvious coding difference found.
MRG1:
Variant: MRG1_R20B
No obvious difference found in the domains I saved.
EPS:
EPS205_ZF
Variant: EPS205_ZF_EPS213_2305
EPS itself had no internal fault memory and the live values looked reasonable:
  • Steering angle approx. -1°
  • Rack position approx. -1 mm
  • Torsion bar torque approx. -0.08 Nm
  • State: NORMAL_OPERATION
The problem is that the PTCU SMR-D file for this vehicle is too new for my DTS Monaco 8.14 installation, so I cannot properly inspect the PTCU coding.
My question is:
Does anyone know exactly what the Autoland iSCAN “Disable ECO” retrofit changes on these newer Mercedes vehicles?
Is it changing:
  • PTCU?
  • CPC_NG?
  • EZS213?
  • BC_F213?
  • more than one ECU?
  • a DID/adaptation instead of normal variant coding?
I am specifically trying to identify the ECU, DID, routine or variant coding changed by this function.
I am NOT asking about normal 3S LastMode coding. I already know the CPC_NG LastMode parameter.
I want to understand how the Autoland iSCAN performs the complete “Disable ECO” retrofit and why it can create a configuration mismatch.
If anyone has compared the vehicle before/after this function, or knows the exact coding/DID involved, I would really appreciate the information.
Thank you.
Thanks given by:
2
When you use those types of options, you lose control over what has been modified; it is much safer and more effective to do it manually with the corresponding backups.
Thanks given by:
3
Your scantool just mess up coding. Nothing more. Do you remember what is the purpose of this test?
MBRetrofit Map Codes, Remote Star3 Coding  
Thanks given by:
4
Thank you.

The purpose was to completely disable the ECO Start/Stop function at the customer's request.

I already know how to use CPC_NG 3S LastMode, but in this case the customer originally requested a complete Start/Stop disable, not LastMode.

The Autoland iSCAN had a dedicated retrofit function:

EZS213 → Retrofit → ECO → Disable ECO

So I tested this function.

It did disable Start/Stop as intended, but afterwards U0420EA and a parking assist warning appeared. PTCU also temporarily stored P164400 (incorrect variant coding/configuration).

After using “Enable ECO” again, Start/Stop returned to normal and all of those faults disappeared.

That is why I am now trying to understand exactly what the scan tool modified.

I agree that manual coding with backups is much safer.

Do you know which ECU or coding parameter is normally used for a complete ECO Start/Stop disable on this X290 generation, other than 3S LastMode?
Thanks given by:
5
CPC_NG
DTS9.04.016
MB software
206223coding
M6+ Pro,C3
DS,Citroen,Peugeot Online
Lexus online//DST010
Thanks given by:
6
Thank you.

Do you know the exact parameter / domain / DID in CPC_NG for the complete Start/Stop disable?

I already checked Domain [001] and I can see:

- 3S LastMode
- intelligente Motorabschaltung iECO
- Kopplung 3S an Fahrprogramme

But I am specifically looking for the complete disable used by the Autoland iSCAN function, not 3S LastMode.

If you know the exact CPC_NG parameter or service, could you please point me in the right direction?

Thank you.
Thanks given by:
7
(11 hours ago)wkjbt644 Wrote: Thank you.

The purpose was to completely disable the ECO Start/Stop function at the customer's request.

I already know how to use CPC_NG 3S LastMode, but in this case the customer originally requested a complete Start/Stop disable, not LastMode.

The Autoland iSCAN had a dedicated retrofit function:

EZS213 → Retrofit → ECO → Disable ECO

So I tested this function.

It did disable Start/Stop as intended, but afterwards U0420EA and a parking assist warning appeared. PTCU also temporarily stored P164400 (incorrect variant coding/configuration).

After using “Enable ECO” again, Start/Stop returned to normal and all of those faults disappeared.

That is why I am now trying to understand exactly what the scan tool modified.

I agree that manual coding with backups is much safer.

Do you know which ECU or coding parameter is normally used for a complete ECO Start/Stop disable on this X290 generation, other than 3S LastMode?
So you want to understand what parameter the tool claim to change even if is a wrong solution as you already find out?
MBRetrofit Map Codes, Remote Star3 Coding  
Thanks given by:
Users browsing this thread: