To obtain your registration code, please send an email to [email protected]
Thread Rating:
  • 14 Vote(s) - 2.93 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Pano roof motor change on w221 S550

1
Have a friend that has a pano roof problem on an S550. The motor appears to have seized. Is this a pretty difficult job? Does the entire headliner need to be dropped?

Thanks!

Also, resyncro in DAS is not effective, and moves the roller blind with glass open?
I am not a robot.  I can identify crosswalks, busses, cars, traffic lights, and mountain ranges.
Thanks given by:
2
not be removed all ceiling
if you just change the driving motor panoramic sunroof! , Changes in 30 minutes
Column A panels dismantled,
support glasses
Control board ceiling
sunshades
door seals and front pillar trim column B ,partially
Unclip the ceiling in the front section
change song and \
fit everything back
do not forget press to [Image: postbit_thx.gif] and [Image: postbit_reputation.gif]
good luck
Thanks given by: e500
3
The hall sensor is also reading wrong in DAS for the roller blind so it tries to close above its limits. Not sure it there are additional isssues or not. Roller blind moves fine, but attempts to move it beyond its limits. Unsure if glass motor is only issue or not.
I am not a robot.  I can identify crosswalks, busses, cars, traffic lights, and mountain ranges.
Thanks given by:
4
you tried to teach him again?
not remember if she menu for curtain-visor adapatare
do not forget press to [Image: postbit_thx.gif] and [Image: postbit_reputation.gif]
good luck
Thanks given by:
5
Yes. Teach in moves the roller blind in front forward beyond its limits, and shows a value in Actual Values much higher than normal (100x normal) but this value does change when it is moved. Actuating the glass clicks the motor but glass does not move. Disconnecting the motor, the relay can be heard clicking and when the motor is connected you can hear it attempting to move glass but it does not move, but the OCP panel lights dim like it is attempting.

What are the main symptoms of glass motor failure?

Thanks
I am not a robot.  I can identify crosswalks, busses, cars, traffic lights, and mountain ranges.
Thanks given by:
6
(10-15-2016, 12:52 AM)e500 Wrote: Yes. Teach in moves the roller blind in front forward beyond its limits, and shows a value in Actual Values much higher than normal (100x normal) but this value does change when it is moved. Actuating the glass clicks the motor but glass does not move. Disconnecting the motor, the relay can be heard clicking and when the motor is connected you can hear it attempting to move glass but it does not move, but the OCP panel lights dim like it is attempting.

What are the main symptoms of glass motor failure?

Thanks

there should be a plastic circular clip on the headliner thats covered up by the drivers sunvisor. Pop that clip off and there should be the hex for the sunroof motor to manually turn it with a wrench. The electrical part of the motor have failed but the mechanical part may still be functional.
Thanks given by:
7
(10-15-2016, 02:50 AM)benztech823 Wrote:
(10-15-2016, 12:52 AM)e500 Wrote: Yes. Teach in moves the roller blind in front forward beyond its limits, and shows a value in Actual Values much higher than normal (100x normal) but this value does change when it is moved. Actuating the glass clicks the motor but glass does not move. Disconnecting the motor, the relay can be heard clicking and when the motor is connected you can hear it attempting to move glass but it does not move, but the OCP panel lights dim like it is attempting.

What are the main symptoms of glass motor failure?

Thanks

there should be a plastic circular clip on the headliner thats covered up by the drivers sunvisor. Pop that clip off and there should be the hex for the sunroof motor to manually turn it with a wrench. The electrical part of the motor have failed but the mechanical part may still be functional.

The hex part of the motor is unfortunately seized to the point the bolt is stripped. I find it odd that the both the roller blind and the glass are not functioning correctly. Not sure if the hall effect sensors have failed or what it could be. Still diagnosing it.
I am not a robot.  I can identify crosswalks, busses, cars, traffic lights, and mountain ranges.
Thanks given by:
8
hall sensor is incorporated in the electric motor
see you can have surprises to change the electric motor and hatch have mechanical problems on the trigger levers and hinges.
get off the electric motor cover Loosen the worm wheel,
between lid and wheel spacer washer put, I guess you drive teeth salt,
you can turn worm wheel and mount and vice versa, but you do not forget to put the washer. so you can pick the place if worn Pinon Drive for Cable
after doing some shares closed maximum fit and maximum open and hold down the button until you hear decoupling relay, then just learn the new position. These are all valid if the mechanical elements work well and have not broken
sorry but I I wanted to write to you quickly and I used translator, I hope to be understood what I tell them
do not forget press to [Image: postbit_thx.gif] and [Image: postbit_reputation.gif]
good luck
Thanks given by: e500
9
Hope to help friend remove it tomorrow and will know more. Will post what I find.
I am not a robot.  I can identify crosswalks, busses, cars, traffic lights, and mountain ranges.
Thanks given by:
Users browsing this thread: