To obtain your registration code, please send an email to [email protected]
Thread Rating:
  • 14 Vote(s) - 2.86 Average
  • 1
  • 2
  • 3
  • 4
  • 5

VVDI MB can't connect to ECU

10
I connected the cables from VVDI MB tools OBD to ECU directly. Every function is fine. If you using ECU adapter cable, please check did the can high and can low of the plug is short circuit. Some times there will have short circuit on the serial port of the ECU adapter
Thanks given by: daxxer , craig coopen , BigK , jemilalicheroy
11
I tried to go directly, and it is still the same.


I added 2 120ohm resistors, in series, for CAN L, and CAN H, or do I bridge them?(parallel)


I have tried every combination.
Thanks given by:
12
(09-26-2016, 10:27 PM)BigK Wrote: I tried to go directly, and it is still the same.
I added 2 120ohm resistors, in series, for CAN L, and CAN H, or do I bridge them?(parallel)
I have tried every combination.

no need any resistors in series, when you don't understand basic knowlege about direct CAN connection to alone ECU without car only on bench, then forget to get any results... Listen
_Offer TOKENS for VVDI MB BGA Tool or all VVDI2 activations - Instant_


Thanks given by: craig coopen
13
(09-26-2016, 10:35 PM)daxxer Wrote:
(09-26-2016, 10:27 PM)BigK Wrote: I tried to go directly, and it is still the same.
I added 2 120ohm resistors, in series, for CAN L, and CAN H, or do I bridge them?(parallel)
I have tried every combination.

no need any resistors in series, when you don't understand basic knowlege about direct CAN connection to alone ECU without car only on bench, then forget to get any results... Listen

I know it's part of the game, but sorry for my frustration for trying to fix a brand new product I just purchased. I read Line Theory, and realize two terminating resistors is best. But regardless, if there was an quality control, I probably wouldn't be posting and wasting time.
Thanks given by:
14
(09-26-2016, 11:04 PM)BigK Wrote: I know it's part of the game, but sorry for my frustration for trying to fix a brand new product I just purchased. I read Line Theory, and realize two terminating resistors is best. But regardless, if there was an quality control, I probably wouldn't be posting and wasting time.

yes, i understand you...when you want to have sure about your VVDI unit, then try to read some other ECU, no need renew it, only try to read it... Pc

about the resistor 120 ohm value for using by CAN lines, its a basic knowlege, why and where must be this resistor used as "end terminator" for success data reading...Listen
_Offer TOKENS for VVDI MB BGA Tool or all VVDI2 activations - Instant_


Thanks given by:
15
Just make direct connection from OBD2 to ECU and give power supply.
In my case I'm not using resistance Listen

OBD2 side:
http://pinoutsguide.com/CarElectronics/m...nout.shtml

ECU Side:
2: Ground
15 & 16: 12 Volts
41: CAN High
54: CAN Low

Best regards.
[Image: mhhsig.gif]
16
(09-28-2016, 01:38 AM)webmaster Wrote: Just make direct connection from OBD2 to ECU and give power supply.
In my case I'm not using resistance Listen

OBD2 side:
http://pinoutsguide.com/CarElectronics/m...nout.shtml

ECU Side:
2: Ground
15 & 16: 12 Volts
41: CAN High
54: CAN Low

Best regards.

I have tried this as well, with several ECUs now with no luck.

I am not sure if it's a faulty VVDI, or something trivial I am not noticing
Thanks given by:
17
(09-22-2016, 11:32 PM)IGNASIO88 Wrote: ME97 connected to - data read from ECU, did not try to reset. Check the scheme of connection.

right Nod

BigK: check the wiring, sure must be somewehre some miniatur fault... Listen

(09-28-2016, 01:38 AM)webmaster Wrote: Just make direct connection from OBD2 to ECU and give power supply.
In my case I'm not using resistance Listen
OBD2 side:
http://pinoutsguide.com/CarElectronics/m...nout.shtml
ECU Side:
2: Ground
15 & 16: 12 Volts
41: CAN High
54: CAN Low
Best regards.

[Image: scheme.bigk.jpg?ver=0]
_Offer TOKENS for VVDI MB BGA Tool or all VVDI2 activations - Instant_


Thanks given by: Rocinante , ould
Users browsing this thread: