To obtain your registration code, please send an email to [email protected]
Thread Rating:
  • 47 Vote(s) - 2.72 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Star C4 Sd Connect Lan connection problem

19
I have the same with my multiplexer experienced tonight just three hours geschlafen.In my case it has been found that the contacts on the board out of order waren.Die settings from Mux can delete located in an INI file in the same folder as SD Toolkit. Sorry for my English.
automotiveforum.net SCAMMER forum
Thanks given by: GolfmkI
20
(09-28-2016, 06:02 PM)kashalot Wrote: I have the same with my multiplexer experienced tonight just three hours geschlafen.In my case it has been found that the contacts on the board out of order waren.Die settings from Mux can delete located in an INI file in the same folder as SD Toolkit. Sorry for my English.

Can you be more specific??

Like other users I have same problem.

NO LAN!!

Tried any cable, and any pc.

Like nothing is connected.

I have whole unit opened.

Cant see anything wrong

What contacts did you mean??

Any help will be appreciated
Thanks given by:
21
I have my multiplexer apart and have seen that the circuit boards were loose. And currently for Xentry I use Windows XP since there are under Windows 7 many problems, especially WLAN connection breaks off again and again.
automotiveforum.net SCAMMER forum
Thanks given by: GolfmkI
22
(04-10-2015, 10:01 PM)testariauto Wrote: I have the same problems, it was from lan (mother - situated on sd c4). I have solved for the moment using some plastic issues for keep my lan cable (father), but i serch a lan for replace the un standard that i have.

Can you be more specific??
I cannot find anithing loose when opening machine .
I cannot understand also how did you exactly solve the problem.

Thanks beforehand
Thanks given by:
23
This are my Mux

I have seen many of them and this seems "good quality".

I dont find bad quality or even missing components like many others and connectors are better..

Machine boots ok...

But as I cannot connect via Lan cable is UNUSABLE rigth now.Its possible its a 100% working unit but as you KNow first stages requires Lan connection to enable wifi and other configs...

As you can figure out when machine boots 100% it appears on screen device not in use . Simply because cable "is not connected".

I have checked all connectors specially those from mini lan board but dont success.

As you can see on pictures I opened whole unit and I am testting it on bench....

But lan is not working....

LIke no cable is connected

Keep fighting!!

[Image: 20161116_120254.jpg]

[Image: 20161116_120309.jpg]

[Image: 20161116_120319.jpg]
Thanks given by:
24
(11-16-2016, 04:10 PM)GolfmkI Wrote: This are my Mux

I have seen many of them and this seems "good quality".

I dont find bad quality or even missing components like many others and connectors are better..

Machine boots ok...

But as I cannot connect via Lan cable is UNUSABLE rigth now.Its possible its a 100% working unit but as you KNow first stages requires Lan connection to enable wifi and other configs...

As you can figure out when machine boots 100% it appears on screen device not in use . Simply because cable "is not connected".

I have checked all connectors specially those from mini lan board but dont success.

As you can see on pictures I opened whole unit and I am testting it on bench....

But lan is not working....

LIke no cable is connected

Keep fighting!!

[Image: 20161116_120254.jpg]

[Image: 20161116_120309.jpg]

[Image: 20161116_120319.jpg]

If your SDC clone does not "see" LAN connection, *PC does not detect it on LAN port, and your IP config on PC is OK* then, either:

1. You have bad LAN connector or hardware failure on LAN connector PCB Sadsmile

2. Your NetPhy IC on MCU board is gone. Sadsmile

In both cases you have hardware failure/error and it can not be resolved with any software or firmware programming Sadsmile

Regards!
Thanks given by:
25
What do for Windows they use? Has everything already functioned?
automotiveforum.net SCAMMER forum
Thanks given by:
Users browsing this thread: