ODIS Service 5.2.6 by FANTOMEL , Postsetup 98.0.140, 98.0.160,98.0.210 -Torrent

Hi 

I am having 2 error one when i was extracting the zip file and the other one when i am installing the postsetup file. kindly advice with these error, Thanks in advance.

From what I experienced during installation and read every were, you should always run the ODIS as administrator

Any expert that could also give some tips about using ODIS to complete ignorants? :s
I really need it.

When i run as administrator, the postsetup start for a minute and the below error pop up. any one can advice. Thanks.

Hi 

I am having 2 error one when i was extracting the zip file and the other one when i am installing the postsetup file. kindly advice with these error, Thanks in advance.

From what I experienced during installation and read every were, you should always run the ODIS as administrator

Any expert that could also give some tips about using ODIS to complete ignorants? :s
I really need it.

When i run as administrator, the post setup start for a minute and the below error pop up. any one can advice. Thanks.

Hi,
Finally the installation and post setup done successfully after several attempt, while I am doing post setup there was massage pop up to install the net frame 3.5 when I have installed the net frame 3.5 then the post setup completed successfully. could be the net frame issue. Any advice if I can install the latest version 6.2 without uninstalling the old 5.2.6 version.. thanks

Hw id 
5720E-1CDD4-C55F5-83B88


Activation key olz

Name : automotive.aura

HW id : 5720E-1CDD4-C55F5-83B88

key : ARH26HOu3qbaT74LI6qC4SpoAIuavaMGTeMhXUYuMs4+PeLuzmLqB2vwfQAKmO02l10KXh5flpclRFNmsI9uUcx1g9y9Gceldj70vgKzusTiS5B8urUvlQ4

Hi,

First of all thanks!! I installed 5.2.6, replaced the launcher and did both updates. However when b I launch Odis it still need group login information?! This way I can’t start a diagnosis.

Any suggestions are welcome 🙏

HW ID:
C67FE-1CDD4-C55F5-8C0EE

THANKS!

HW ID:
C67FE-1CDD4-C55F5-8C0EE

THANKS!

Name : cybertorte



HW ID: C67FE-1CDD4-C55F5-8C0EE



Key : MPjw2zu75uea=mZDfO5PlVSlA1XuYhF42UpvsJUQk7S5V1lHqrsAeoIse+cQDFgRwD4DbE0DFdmpXqXNo9iS+5wlZK+zFIkTOVw8d07w44f+aE8ii8TSpu0

how to install please

For version 5.2.6 running 98.0.160....

Download Torrent 1, Torrent 2, Torrent 3 and Key Generator.

Make sure you have Java installed on your computer and it's up-to-date. https://www.java.com/ES/download/

When completed, go to folder "Odis - S 5.2.6 without updates and postsetup"

Install "0.MS_Visual_C++2010 for W10". If you already have it, it'll tell you and don't bother.

If you are using Windows 7, install the appropriate updates in either "0.Prerequirements x64 W7" for 64-bit systems or "x86" for 32-bit systems.

Install ODIS with "1.OffboardDiagSetup-Service_VWMCD_5_2_6-B52_6_0_2"

- Select your diagnostic interface. If you use 6154, select it and click next. If you use PassThru, select it and click next. If you use more than one, select one, click next, go back, select another, click next, etc. If you use an older 6054 interface, there are other instructions that I cannot help you with.

Install will ask you for license file, direct it to the "license.dat" file located in "2.ODIS-S 5.2.6 Patch+License-Full"

Install will ask you for some PostSetup configuration data, direct it to the folder "ODIS-Service_update_5_2_6-EU_20200317_98.0.140" (Torrent 2)

Complete installation.

Once completed, copy "OffboardDiagLauncher.exe" to the ODIS installation folder. (mine is "C:\Program Files (x86)\Offboard_Diagnostic_Information_System_Service")

Launch ODIS... To get past the "Warnings/notes", scroll to bottom and click OK.

At some point, I forget when, ODIS will ask you for registration information. Naturally, this is where the Key Generator is used.

Enter your registration name...
Click "Hardware ID" and paste your HWID from the ODIS registration prompt...
Click "Generate" and copy your registration key to the ODIS registration prompt...

ODIS should prompt you about an update server. Similar to PostSetup configuration data, direct it to the folder "ODIS-Service_update_5_2_6-EU_20200317_98.0.160" (Torrent 3)
It should then begin updating to the 98.0.160 data.
--- IF IT DOES NOT DO THIS ---
Click Admin
Go to Connections tab
Click Mirror Server 2
for Mirror server URL select the 98.0.160 folder (Torrent 3)
Save

In the right pane, expand Extras and click Update. Data should begin updating to 98.0.160

ODIS-S 5.2.6 with Postsetup 98.0.140, 98.0.160, 20200414_98.0.210 and some extra options.

THE ONLY MISSING BRAND IN ACTIVATION IS MAN

Torrent 1
0.MS_Visual_C++2010 for W10
0.Prerequirements x64 W7
0.Prerequirements x86 W7
1.OffboardDiagSetup-Service_VWMCD_5_2_6-B52_6_0_2
2.ODIS-S 5.2.6 Patch+License-Full After Unrar this the password for the 7zip archive is as always fantomel
3.PDU-API_fix_x86+x64 for W10
5.Bad VAS5054A Patch
5a.Softing_PDU-API_1.20.42 for clones
EN SFD-Manual for UMB.pdf
EN Windows 7 Announcement UMB.pdf
supportnews-en.pdf

Torrent 2
4.ODIS-Service_update_5_2_6-EU_20200317_98.0.140

Torrent 3
ODIS-Service_update_5_2_6-EU_20200330_98.0.160

Torrent 4
4a.ODIS-Service_update_5.1.6_v89.5.520 to 5.2.6-EU_20200303_96.0.10

Torrent 5
4b.ODIS-Service_update_5.1.6_v89.5.520 to 5.2.6-EU_20200317_98.0.140


How to install https://mhhauto.com/Thread-ODIS-Service-...ent?page=3 thanks to @[b][b]Meat[/b][/b]

[b]Sorry ...the life is litle complicated for the moment![/b]

Does it work with vas5054a clone?