To obtain your registration code, please send an email to [email protected]
Thread Rating:
  • 17 Vote(s) - 2.59 Average
  • 1
  • 2
  • 3
  • 4
  • 5

License plate light W204

1
Hi M8

I have retrofit the License plate light to LED.

It is a plug and Play version. Right now I got a fault mesage in SAM_R
(B177115 Signal light in Trunklid right circiut / no funktion/......)
The lights are working.

What part is to code in vediamo?
Help is appreciate.

Thanks
Spark
Thanks given by:
2
(10-28-2016, 08:51 PM)spark Wrote: Hi M8

I have retrofit the License plate light to LED.

It is a plug and Play version. Right now I got a fault mesage in SAM_R
(B177115 Signal light in Trunklid right circiut / no funktion/......)
The lights are working.

What part is to code in vediamo?
Help is appreciate.

Thanks
Spark

Better to post a picture from your diagnostic, your translate can suggest the light from inside the trunk...
MBRetrofit Map Codes, Remote Star3 Coding  
Thanks given by:
3
You can check the rear SAM codings to find settings for the license plate that have been set to "bulb" and try to change them to "led" and see if this fixes the problem. W204 with the new side markers on the mirrors should at least have these.
Thanks given by: spark
4
Or you buy better qality of led lights,maybe is easier....
Thanks given by: pakiguy
5
(10-28-2016, 11:45 PM)trigital Wrote:
(10-28-2016, 08:51 PM)spark Wrote: Hi M8

I have retrofit the License plate light to LED.

It is a plug and Play version. Right now I got a fault mesage in SAM_R
(B177115 Signal light in Trunklid right circiut / no funktion/......)
The lights are working.

What part is to code in vediamo?
Help is appreciate.

Thanks
Spark

Better to post a picture from your diagnostic, your translate can suggest the light from inside the trunk...

I have problems with the lights inside the trunk too. All LED's are with resistors. All other LED's inside the car are working propperly and they are all from the same distributor.
I have searched the Bulb thing in te SAM rear but cant find anything. The only thing what is found is a setting with 12,3 Volt.
Any further suggestions
Thanks

Attached Files Thumbnail(s)
   
Thanks given by:
6
(10-30-2016, 03:59 PM)tamba Wrote: Or you buy better qality of led lights,maybe is easier....

Agreed

don't reinvent the wheel
Thanks given by: Rocinante
7
(10-28-2016, 08:51 PM)spark Wrote: Hi M8

I have retrofit the License plate light to LED.

It is a plug and Play version. Right now I got a fault mesage in SAM_R
(B177115 Signal light in Trunklid right circiut / no funktion/......)
The lights are working.

What part is to code in vediamo?
Help is appreciate.

Thanks
Spark

As my understanding, in Rear SAM has less control coding than front SAM, the license plate light can be turned off by using DAS developer or VEDIAMO, but you can't suppress the error message from Rear SAM.

Fellows, please correct me if I am wrong.
I have realized how important that giving thanks to the people who had ever provides little help, if you think so, please simply click thanks for me if you found any of my post is useful Smile
Thanks given by:
8
(01-18-2017, 10:45 AM)master9999 Wrote:
(10-28-2016, 08:51 PM)spark Wrote: Hi M8

I have retrofit the License plate light to LED.

It is a plug and Play version. Right now I got a fault mesage in SAM_R
(B177115 Signal light in Trunklid right circiut / no funktion/......)
The lights are working.

What part is to code in vediamo?
Help is appreciate.

Thanks
Spark

As my understanding, in Rear SAM has less control coding than front SAM, the license plate light can be turned off by using DAS developer or VEDIAMO, but you can't suppress the error message from Rear SAM.

Fellows, please correct me if I am wrong.

Of course you can surpress the error messages. It is in Fehlercodefreigabe.
Thanks given by: Rocinante
9
(01-18-2017, 12:18 PM)Aless91 Wrote:
(01-18-2017, 10:45 AM)master9999 Wrote:
(10-28-2016, 08:51 PM)spark Wrote: Hi M8

I have retrofit the License plate light to LED.

It is a plug and Play version. Right now I got a fault mesage in SAM_R
(B177115 Signal light in Trunklid right circiut / no funktion/......)
The lights are working.

What part is to code in vediamo?
Help is appreciate.

Thanks
Spark

As my understanding, in Rear SAM has less control coding than front SAM, the license plate light can be turned off by using DAS developer or VEDIAMO, but you can't suppress the error message from Rear SAM.

Fellows, please correct me if I am wrong.

Of course you can surpress the error messages. It is in Fehlercodefreigabe.


Thank you Aless91, learnt from you again! you are really knowledgeable person in MB world! (not only, but also)
I have realized how important that giving thanks to the people who had ever provides little help, if you think so, please simply click thanks for me if you found any of my post is useful Smile
Thanks given by: workshop369 , Bazy
Users browsing this thread: 1 Guest(s)